This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
22 sickle bar Broken
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
22 sickle bar Broken
I have a 22 sickle bar and I think i need to do some welding.
I believe this plate should be welded to the flywheel shaft tube
can any one confirm this?
I believe this plate should be welded to the flywheel shaft tube
can any one confirm this?
-
- 10+ Years
- Posts: 251
- Joined: Sat Aug 25, 2007 9:26 pm
- Zip Code: 98828
- eBay ID: elkshead
- Tractors Owned: Farmall M 1943 for parts
Farmall M 1944 Restored
Farmall A 1940 Restored
TD 6 1940 w/ Holt Blade
TD 6 1953
1952 Cub Restored
1962 Cub Lowboy - Circle of Safety: Y
- Location: Malaga, WA 98828 Chelan County
Re: 22 sickle bar Broken
If thats the correct end..... the plate is welded to the round cover, not the tube.
I've never used mine, maybe it should be welded? I'll look closer tomorrow.
-
- 10+ Years
Re: 22 sickle bar Broken
No, it is the other end, the end that the pitman arm attaches to.
-
- Team Cub
- Posts: 17279
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: 22 sickle bar Broken
Yes, it should be welded. Also, if your coupling bar has the big bend that it appears to have in the first picture, you need to fix that too. Based on what it would take to bend the coupling bar, you should check the cutter bar for bends too.
-
- 10+ Years
Re: 22 sickle bar Broken
Thanks, I could not tell from the manual, it shows the plate attached in one view and not in another. yes I do plan on fixing the coupling bar too. Dad hit a rock with the mower and said it stopped him dead, you can't tell in the picture of the un-attached plate but that it was bent too. The cutter bar is OK, he hit right in the center of the tractor. I have all the new teeth, rivots and wear plates just need to find some of that International Blue paint. anyone have on online source, or know where i can find it here in Taxachusetts
-
- Team Cub
- Posts: 17279
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: 22 sickle bar Broken
I've used Van Sickle 460 International Blue and been happy with it. You can get it from Ken Updike at Carter & Gruenewald.
http://www.cngco.com/
Kenneth Updike Parts /Internet/ Toy Sales 608.455.2411 Brooklyn kenu@cngco.com
Here is a recent thread on paint:
http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=64132
http://www.cngco.com/
Kenneth Updike Parts /Internet/ Toy Sales 608.455.2411 Brooklyn kenu@cngco.com
Here is a recent thread on paint:
http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=64132
-
- 10+ Years
Re: 22 sickle bar Broken
Thanks Jim, Paint is on the way, I will post some more pictures as I progress on this restore/repair...
-
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: 22 sickle bar Broken
Pretty hard to weld the tube to the hanger because of the bronze bushing inside the tube. The heat will melt the expensive bushing. What I did was make a set screw with a jamb nut on the belt adjuster to hold the tube tight to the pulley shield. This keeps it in place and also keeps the tube from rotating. It is working well for me.
"Courage is being scared to death-but saddling up anyway".......John Wayne
-
- Team Cub
- Posts: 17279
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: 22 sickle bar Broken
BIGHOSS wrote:Pretty hard to weld the tube to the hanger because of the bronze bushing inside the tube. The heat will melt the expensive bushing.
Good point. Another option is to pull the bushing while welding then reinstall it. It would be a good idea to look at the wear on the bushing before starting. There may be some benefit to turning it 90 degrees when reinstalling it.
-
- 10+ Years
Re: 22 sickle bar Broken
I am going to replace that bushing mine is worn down, problem is the shaft is worn on that end also. I am going to make a up a split bushing out of oil-lite bronze as the pully end of the shaft is larger than the pitman end. I will need to slide the shaft in almost all the way then push in the split bushing in the tube.
-
- Team Cub Mentor
- Posts: 17489
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
Re: 22 sickle bar Broken
Original paint and decals on mine. All red, except for the pitman and grass rod assembly. Those are cream.
-
- 10+ Years
- Posts: 2917
- Joined: Sat Feb 11, 2006 5:26 pm
- Location: NC
Re: 22 sickle bar Broken
I suggest disassembling the mower for inspection and repair/replacement of every damaged part. Welding is easier when access is better and positioning is possible. For that weld, I doubt that the bushing will be damaged. Copper plates are used to back up the weld area on sheet metal repairs when MIG welding rust perforated areas. Copper and it's alloys wick heat away rapidly. I would weld the broken part with 7018 electrodes, not MIG. Contrary to conventional practice, I would consider leaving all the existing weld to aid in proper alignment, tack the parts thoroughly (6011 electrode is good for this) , and then grind limited portions and weld there before grinding the opposite area and welding it .
I built up the badly worn pulley end of the mower tube with MIG and ground it back to shape with no damage to the bushing.
I built up the badly worn pulley end of the mower tube with MIG and ground it back to shape with no damage to the bushing.
Luck favors those who are prepared
-
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: 22 sickle bar Broken
I learned to weld many moons ago with 6010 DC and 6011 AC rods. But, after burning a few 7014 rods, It became my rod of choice. 7014 is not a low hydrogen rod as the 7018. A little moisture in a 7014 does not hurt the welding. 7018 needs to be kept very dry. Just MHO.
"Courage is being scared to death-but saddling up anyway".......John Wayne
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: 22 sickle bar Broken
I used to prefer 6011's because that is what I learned on with Dad. Now after my course I have become a little wiser/accustomed to different rods and different types of welding. 7014's are now my rod of choice. Lots of metal gets laid on rather quick and good flow. I keep my rods in the plastic sealed rod keepers. My
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
Re: 22 sickle bar Broken
What type of wood do you make a new pitman arm out of ?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2
- 391
-
by Stanton
Sat Jun 05, 2021 7:16 am
-
-
NH 451 Sickle mower leg dimensions Attachment(s)
by Poncho » Fri Aug 13, 2021 9:05 pm » in Other Tractors and Machinery - 8
- 677
-
by Poncho
Sat May 28, 2022 9:36 pm
-
-
-
IH Sickle Mower Identification Attachment(s)
by Tired_Iron » Fri Jan 14, 2022 1:38 am » in Other Tractors and Machinery - 11
- 1378
-
by Tired_Iron
Tue Jan 18, 2022 10:41 am
-
-
-
451 nh sickle mower to L 4060 kubota Attachment(s)
by Poncho » Sun Aug 01, 2021 8:41 am » in Other Tractors and Machinery - 4
- 646
-
by Poncho
Tue Aug 03, 2021 4:44 pm
-
Return to “Other Tractors and Machinery”
Who is online
Users browsing this forum: No registered users and 0 guests