Here's one of the sawblades that I got with the radial arm saw deal.
It's 11" in diameter, and it's a Simond's.
There are just very sharp points, with the edge on alternating sides.
It looks like it can be mounted to cut in either direction?
Anyway, what's this saw blade designed to cut guys?
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
What is this Sawblade for?
-
- 10+ Years
- Posts: 688
- Joined: Sat Mar 29, 2003 4:17 pm
- Zip Code: 00000
- Tractors Owned: 1957 International Cub Loboy; C-3 finish mower; L-54 blade; L-F194 plow incl coulter and jointer;L-38 disk harrow. Leinbach FH back blade.
- Circle of Safety: Y
- Location: Canton, Ohio
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: What is this Sawblade for?
That appears to be one of the original hollow ground plywood blades. Meant for laminated veneer, when properly sharpened they left a very clean cut with minimal tearout. You don't see many of them used anymore, most shops no longer sharpen their own blades. They have usually been superseded by carbide crosscut blades for radials and usually 100 TPI ATB or Triple Chips for different laminates/cores.
I still have a couple of the old plywood blades my Dad had back in the 60's. Simmonds were a top name back then. Same company made the files used to sharpen them -- the triangular shaped files. I also have a replica of the blade clamp Dad had made to sharpen them on the bench. I still love to hear the sound of a sharp file as it cuts across the teeth. Needed to have a saw set as well to re-set for the kerf. This was a long time before the thin-kerf blades came on the market.
And NO! You cannot mount it in either direction. Follow the owner's manual for mounting blades. In general teeth should always rotate forward as in to the front of the table be it a table or radial arm saw.
I still have a couple of the old plywood blades my Dad had back in the 60's. Simmonds were a top name back then. Same company made the files used to sharpen them -- the triangular shaped files. I also have a replica of the blade clamp Dad had made to sharpen them on the bench. I still love to hear the sound of a sharp file as it cuts across the teeth. Needed to have a saw set as well to re-set for the kerf. This was a long time before the thin-kerf blades came on the market.
And NO! You cannot mount it in either direction. Follow the owner's manual for mounting blades. In general teeth should always rotate forward as in to the front of the table be it a table or radial arm saw.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
Re: What is this Sawblade for?
Blywood blades work well when reversed for cutting sheet metal, aluminum, steel building siding etc.. WEAR GOGGLES!!
-
- Cub Pro
- Posts: 7760
- Joined: Mon Jun 22, 2009 6:56 am
- Zip Code: 64070
- Tractors Owned: 1942 Farmall AV, serial #87025
1947 Farmall Circle Cub, serial #2116
1948 Farmall Cub, serial #46066 - Circle of Safety: Y
- Location: Lone Jack, MO
-
- 10+ Years
- Posts: 122
- Joined: Wed Oct 26, 2011 9:16 am
- Zip Code: 30549
- Tractors Owned: 62 Cub Lowboy
76 Ford 1600
555 Ford backhoe
67 Cub
Economy Jim Dandy
69 Massey Ferguson 135
Yanmar 2700
Case 1840 skid steer
2 - John Deere model 112 - Location: Georgia, Jefferson
Re: What is this Sawblade for?
Plywood blade, I've got a little finer tooth one mounted on my table saw right now. Works good on thin plywood, not so good on thicker solid wood.
Roy
Roy
Who is online
Users browsing this forum: No registered users and 0 guests