This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
just want some more information on governor
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 296
- Joined: Sat Sep 08, 2012 10:14 pm
- Zip Code: 14113
just want some more information on governor
i was wondering if the governor on my 1947 farmall cub is working properly? how do they work, and how do you know if it failed. do these things operate like the governor on a small engine, when you put the engine under additional load, it opens the throttle plate on the carburetor. im guessing they have spinning weights? when i put the tractor into 3rd gear from a dead stop it loads the engine down quite a bit until its moving. i have to feather the clutch quite a bit when starting in 3rd gear from a stop. i know these tractors arent the most powerful machines on the planet but i just wondered what is considered normal. does "feathering" the clutch a little cause the clutch to wear out faster, what is considered "ridding the clutch", because i dont want to do that. should the RPM drop significantly when in 3rd gear. my tractor runs good, does not smoke, and has good oil pressure, i just wondered what is normal for these machines, this is my first cub. these tractors arent like cub cadet, that probably have a higher power/weight ratio and do not drop much in RPM's when you let off the clutch. is there any adjustment that i can make to the governor that will open the throttle plate a little more when placed under a load?
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: just want some more information on governor
What you describe is pretty normal. You only have a 10hp engine trying to move nearly a ton of steel in 3rd gear. Having to feather the clutch to get moving in 3rd is normal, how much depends on how well it is tuned, how worn, and how much load. Riding the clutch is when you keep your foot on it and pushed down a little to where the Throwout bearing is partly engaged all the time, and since a cub TO bearing is a graphite block that is hard on them.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
Re: just want some more information on governor
Normal. 3rd is a "road gear". the cub may run good, but unless it is optimal, it can be exactly as you describe. I suggest a full tune up, most importantly, adjust your valve lash. It should approve your 3rd gear opperation.
To check your governor, stand beside the carb and pull on the throttle rod. It should pull back.
To check your governor, stand beside the carb and pull on the throttle rod. It should pull back.
-
- 10+ Years
- Posts: 296
- Joined: Sat Sep 08, 2012 10:14 pm
- Zip Code: 14113
Re: just want some more information on governor
i might check the valve lash come spring, everything else is in decent shape. i removed a couple of spark plugs... fairly new with only normal deposits. checked cap and rotor, fairly new as well.
-
- Cub Pro
- Posts: 5238
- Joined: Sat Sep 08, 2007 3:49 pm
- Zip Code: 25271
- eBay ID: yogiefisher
- Tractors Owned: 37 John Deere A
63 Farmall Cub
53 Farmall Cub
56 Farmall Cub
IH 140
Massey 165 & 250 - Circle of Safety: Y
- Location: WV. Ripley
Re: just want some more information on governor
Full tuneup as Dale said checking everything, small HP so every little bit helps like adjusting the valves. Run some Seafoam through it to clean the valves and piston deposits. Check the compression after all of this to see what the numbers show. Even placing a timing light on it to make sure the distributor advance is working will help. Use the light, rev the engine while watching the mark advance on the front pulley. You would be amazed at how many advances are not working at all on theses little tractors.
Democracy is two wolves and a lamb voting on what to have for lunch. Liberty is a well-armed lamb contesting the vote.
Ben Franklin
-
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: just want some more information on governor
There is an adjustment for the governor: Set the speed lever to half way. Unhook the governor rod that runs from the carb to the governor, open the carb to full and readjust the end plate to fit, plus one additional turn. Can make a huge difference if it is not properly adjusted. Should be re-adjusted each time the carb is removed.
-
- 10+ Years
- Posts: 1087
- Joined: Sun Apr 18, 2010 6:22 am
- Zip Code: 21742
- Tractors Owned: 1955 F Cub (2)
1952 F Cub
1948 F Cub
2155 JD
216 JD - Circle of Safety: Y
- Location: Hagerstown MD
Re: just want some more information on governor
The Cub has a very good governor when it is set up properly. As others have said you must recognize the hp limits of the engine. You can not just pop the clutch and expect the governor to respond. You have to give the governor time to recognize the load and respond. You do this by easing the clutch out slowly until the governor opens the throttle. If this is done properly, it should be a smooth operation without jerks or stalls. The governor will not be activated until the throttle is at a third to half open. Then, you should hear the engine trying to maintain set rpm as load is applied. You can also observe the increased engine exhaust output by watching the muffler cap pivot more open as the governor opens the carburetor throttle plate.
-
- Team Cub Mentor
- Posts: 5641
- Joined: Thu Aug 03, 2006 6:20 am
- Zip Code: 43358
- Tractors Owned: 48 Cub Diesel (Cubota)
53 Cockshutt 20 restored (Shooter)
52 Cockshutt 20 unrestored
47 Leader "B" (Herckie)
49 Leader "D" (Princess)
49 Leader "D" very rough
48 Leader "D" unrestored
Kubota B6200E
Kubota B6200HST
Kubota B8200HST-D - Circle of Safety: Y
- Location: OH West Mansfield
Re: just want some more information on governor
Also, make sure your governor linkage is moving freely. Lubricate to rock shaft pivot, at the left front of the engine, and make sure the linkage rod is not rubbing anywhere. Yes the governor has weights, which constantly work against the external spring located at the top of the governor. Proper linkage adjustment is essential for the governor to function in a responsive, yet smooth manner.
-
- 10+ Years
- Posts: 296
- Joined: Sat Sep 08, 2012 10:14 pm
- Zip Code: 14113
Re: just want some more information on governor
what operates the advance? i didnt know these tractors had any method of advancing timing. i have work on a few chevy small block V8 engines and on them you either have the computer adjusting the advance or a vacuum driven advanced; and when you adjust the distributor the computer OR the vacuum line must be disconnected in order for you adjustments to work. my tractor has the magneto style ignition. by adjusting the "plate" do you mean the rod that attaches the governor to the carburetor?
-
- Team Cub Mentor
- Posts: 5641
- Joined: Thu Aug 03, 2006 6:20 am
- Zip Code: 43358
- Tractors Owned: 48 Cub Diesel (Cubota)
53 Cockshutt 20 restored (Shooter)
52 Cockshutt 20 unrestored
47 Leader "B" (Herckie)
49 Leader "D" (Princess)
49 Leader "D" very rough
48 Leader "D" unrestored
Kubota B6200E
Kubota B6200HST
Kubota B8200HST-D - Circle of Safety: Y
- Location: OH West Mansfield
Re: just want some more information on governor
Actually, with your magneto, there is no advance, in the normal thinking. The mag incorporates an impulse coupling which retards timing during engine start (to top dead center) and as soon as the engine starts, the impulse deactivates and the ignition timing advances and runs at 16deg. advance. Yogi's comment was assuming battery ignition.
-
- 10+ Years
- Posts: 296
- Joined: Sat Sep 08, 2012 10:14 pm
- Zip Code: 14113
Re: just want some more information on governor
so on a cub that someone replaced the mag with a coil and kept the mag distributor no longer has the benefits of having the tractor having ability to advance timing. i have a timing light that i bought to use with my 350 v8 can i use the same timing light or will it not work due to the cub having a 6 volt system?
-
- 10+ Years
- Posts: 7832
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: just want some more information on governor
ad356 wrote:so on a cub that someone replaced the mag with a coil and kept the mag distributor no longer has the benefits of having the tractor having ability to advance timing. i have a timing light that i bought to use with my 350 v8 can i use the same timing light or will it not work due to the cub having a 6 volt system?
Connect it to a 12v and it will work. Just pull your truck/car close if cables are long enough.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: just want some more information on governor
If your timing light has the adjustable advance feature, it will work for a magneto, but if it does not, you will get an incorrect reading since the crankshaft pulley that came with the magneto equipped tractors only had a single mark at TDC, not one for the 16 degree advance. According to the manuals the magnetos only advanced 13 degrees, but checking them I have seen all the way from 13 degrees to 20 degrees. If your timing light does not have the advance feature you can mark the pulley at slightly over 21/32 inch before the TDC mark to adjust it. The main thing with a mag is to make sure it snaps at TDC when turning slowly with a hand crank. If it trips sooner it will tend to kick back and make it hard for the starter to crank, or hurt your hand if you are cranking. If it is late you will have low power.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Team Cub Mentor
- Posts: 20378
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: just want some more information on governor
The addition of an external coil to a magneto was an inexpensive fix when the magneto's internal coil failed.ad356 wrote:so on a cub that someone replaced the mag with a coil and kept the mag distributor no longer has the benefits of having the tractor having ability to advance timing.
Tractor is a 1947 year. Originally had a magneto, but the magneto could have been removed and a battery powered ignition system installed. There are photos of both the magneto and battery powered ignition systems in the operator's manual. Photos can be found on this site of magnetos with the external coil.
As previously suggested, conduct a 100% tune up including compression tests. Guessing you will find the compression on the low side.i have to feather the clutch quite a bit when starting in 3rd gear from a stop.
What is the history of this Cub?
I have an excuse. CRS.
-
- 10+ Years
- Posts: 296
- Joined: Sat Sep 08, 2012 10:14 pm
- Zip Code: 14113
Re: just want some more information on governor
i dont know the full history of my tractor, but it doesnt show signs of being worn out. i has good oil pressure, doesn't consume oil, and doesn't smoke or knock. i pulled a couple plugs.... no oil on the electrode only normal deposits. i assume that if it was worn out it would have poor oil pressure and it would probably burn oil. my tractor has the proper magneto coil. i just wondered what would happen if you replaced the magneto coil with a battery ignition coil
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 211
-
by Don McCombs
Sat Sep 25, 2021 7:34 am
-
- 2
- 221
-
by Bill V in Md
Tue Nov 01, 2022 3:37 pm
-
- 5
- 193
-
by Glen
Sat Sep 03, 2022 6:55 pm
-
- 4
- 304
-
by baldwindiesel
Mon Feb 21, 2022 5:09 pm
-
- 2
- 161
-
by k hutchins
Tue Jun 28, 2022 6:10 am
Who is online
Users browsing this forum: No registered users and 8 guests