This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
regulator problems
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 94
- Joined: Sun Dec 11, 2011 8:21 pm
- Zip Code: 02835
- eBay ID: crazyjoe1078
- Tractors Owned: 56 cub with fast hitch
one point plow
one point harrow - Circle of Safety: Y
- Location: RHODE ISLAND
regulator problems
is it normal after letting a cub sit for the regulator to not work properly ... if i tap it it will charge . just installed it 2 months ago
-
- 10+ Years
- Posts: 5236
- Joined: Tue Jan 12, 2010 2:08 pm
- Zip Code: 12514
- Circle of Safety: Y
Re: regulator problems
Point gap is to wide inside the regulator, I have seen this problem with the foreign regulators, the USA made seem not to have this issue
Tim
Tim
-
- 10+ Years
- Posts: 94
- Joined: Sun Dec 11, 2011 8:21 pm
- Zip Code: 02835
- eBay ID: crazyjoe1078
- Tractors Owned: 56 cub with fast hitch
one point plow
one point harrow - Circle of Safety: Y
- Location: RHODE ISLAND
Re: regulator problems
ok how do i fix this so it dosent happen again can u open it up and adjust the point gap
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: regulator problems
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- Team Cub
- Posts: 17309
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: regulator problems
Be very careful adjusting anything inside the regulator. It is easy to overdo and create another problem. Before making any internal adjustments, make sure you have good conenctions INCLUDING THE GROUNDS.
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: regulator problems
Jim Becker wrote: make sure you have good conenctions INCLUDING THE GROUNDS.
If your new voltage regulator functioned properly when installed, something caused that point gap to open up in a short period of time.
Perhaps the same issue that fried the previous regulator to the point of tapping on it no longer got it to function, or simply poor grounding of the new installation.
This may be reason to pull the hood to closely inspect and service all the charging system connections to prevent further regulator damage if grounding is not an issue.
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- 10+ Years
- Posts: 133
- Joined: Fri Sep 02, 2011 6:22 pm
- Zip Code: 33876
Re: regulator problems
I have the same problem on a Cub Cadet, 12 hp Kolher, Starter/ Generator, VR that worked 3 weeks ago and then wasn't
charging. By putting a jumper wire from the Field post on the Starter/Generator to ground. It would charge that way and when I removed the jumper , the needle on the Ameter would flucuate from charge to 0 and then stop charging. The battery
was not up to full charge, so the points on the VR were not working as they should. I didn't mess with the V/R points as I don't know what they should be.. So far using a battery charger has been the temporary solution.
charging. By putting a jumper wire from the Field post on the Starter/Generator to ground. It would charge that way and when I removed the jumper , the needle on the Ameter would flucuate from charge to 0 and then stop charging. The battery
was not up to full charge, so the points on the VR were not working as they should. I didn't mess with the V/R points as I don't know what they should be.. So far using a battery charger has been the temporary solution.
-
- 10+ Years
- Posts: 1573
- Joined: Sun Feb 02, 2003 11:01 pm
- Zip Code: 36310
- Tractors Owned: 1975 IH cub,1948 farmall cub,1979 international 3200 skid steer and a 1974 John deere 350B dozer.
- Location: Abbeville Alabama
Re: regulator problems
the contact points in the regulator require a cleaning when your described problem occures. especially with the newer aftermarket regulators. Never use sand paper or emery cloth. These will compound the problem in the near future. always use a point file.
Collector of Farmall cubs and cub cadets.Injoy helping people keep their cubs running. Years of experipnce.
-
- 10+ Years
- Posts: 1087
- Joined: Sun Apr 18, 2010 6:22 am
- Zip Code: 21742
- Tractors Owned: 1955 F Cub (2)
1952 F Cub
1948 F Cub
2155 JD
216 JD - Circle of Safety: Y
- Location: Hagerstown MD
Re: regulator problems
If you want to tackle the regulator, the place to start after removing the cover, is the cut out. Do not do anything until you examine whether the cut out points are closed with the engine running at 1/3 to 1/2 throttle and that they open with the engine at low idle. If the cut out points do not close with the engine running at 1/3 to 1/2 throttle, take a non-conductive object and very gently push the moveable point on the cut out toward the fixed point. As you start moving the point, note if the electro magnet picks up the movable point and pulls it closed. Remove your probe and observe if the electro magnet is able to hold the points closed. When the points are closed, either manually or by the electo magnet, check your ammeter to verify that you have a positive charge. It is helpful if you have a friend observe the ammeter as you perform this test. If you have a positive charge when the cut out points are closed, you will need to adjust the cut out point gap or the spring tension holding the movable point open since the electro magnet is not able on its own to pull the movable point to the fixed point. There are two different approaches used in dfferent regulators. In one version, you adjust the spring tension and in the other you bend a small tang that holds the movable point in a pre-set, spring loaded, open position. If your cut out looks like the one pictured in the instructions provided by Rudi, you will need to very slightly screw the adjusting screw in to reduce the spring tension of the flat spring resting on the head of the screw. You only want to reduce the spring tension enough to permit the electro magnet to pull the point closed when the engine is running above low idle. You want the cut out to open when generator output drops off at slow idle. As a precaution, do not make any adjustment on the regulator with a metal screwdriver unless you first disconnect a battery cable. If you feel up to it, give this a try and report back on what you find.
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
Re: regulator problems
crazyjoe wrote:is it normal after letting a cub sit for the regulator to not work properly ... if i tap it it will charge . just installed it 2 months ago
Is it normal? No
As others have posted, you may want to verify the regulator is at fault before you try to adjust. If the regulator is bad then it may just need the points cleaned rather than adjusted. Adjusting a regulator is possible but best done with a voltmeter and ideally with a variable votage supply.
-
- 10+ Years
- Posts: 94
- Joined: Sun Dec 11, 2011 8:21 pm
- Zip Code: 02835
- eBay ID: crazyjoe1078
- Tractors Owned: 56 cub with fast hitch
one point plow
one point harrow - Circle of Safety: Y
- Location: RHODE ISLAND
Re: regulator problems
hey thank for all the advice but it is a ground problem that i fixed last night
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: regulator problems
Thanks for posting the solution to the problem. I see Jim was bang on. Glad it was easily resolved.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 1087
- Joined: Sun Apr 18, 2010 6:22 am
- Zip Code: 21742
- Tractors Owned: 1955 F Cub (2)
1952 F Cub
1948 F Cub
2155 JD
216 JD - Circle of Safety: Y
- Location: Hagerstown MD
Re: regulator problems
I want to echo Rudi's comment and compliment Jim's correct troubleshooting analysis of the problem. On this forum, there have been a number of regulator problems that have been traced to a poor ground. A defective ground could be caused by simple passage of time with rust building up between the regulator bracket and the generator or a new paint job acting as an insulator preventing a good ground contact. Obviously, the regulator needs to be firmly grounded to the tractor frame to complete the circuit back to the battery to permit it to operate in a steady reliable manner. When the regulator has been removed for any reason, attention must be directed at making sure there are clean bare metal surfaces on both the regulator bracket and the generator. As others have said, many times it is the simple to fix possible causes of a problem that should be eliminated first before looking elsewhere. This easy fix suggested by Jim is a good example of practicing this basic rule.
-
- 10+ Years
- Posts: 94
- Joined: Sun Dec 11, 2011 8:21 pm
- Zip Code: 02835
- eBay ID: crazyjoe1078
- Tractors Owned: 56 cub with fast hitch
one point plow
one point harrow - Circle of Safety: Y
- Location: RHODE ISLAND
Re: regulator problems
poor ground wasnt the real problme was more like a rotted out battery box ...
The little thing we over look kick us in the a$$ in the long run.
The little thing we over look kick us in the a$$ in the long run.
-
- 10+ Years
- Posts: 1087
- Joined: Sun Apr 18, 2010 6:22 am
- Zip Code: 21742
- Tractors Owned: 1955 F Cub (2)
1952 F Cub
1948 F Cub
2155 JD
216 JD - Circle of Safety: Y
- Location: Hagerstown MD
Re: regulator problems
Crazyjoe,
The battery box brings up another frequent ground problem with Cubs. Wet cell batteries that use elecrolyte off gas naturally when charging and some of the acid laden electrolyte can eventually run down the sides of the battery to the bottom of the box. This eats up the bottom of the battery box and destroys the ground contact to the tractor frame. Worse yet, it will happen slowly and is mostly invisible. What I did in one situation where the bottom of the box had deteriorated to the point where good contact was no longer certain was to attach another ground cable on the outside of the box using the same bolt that goes through the box and holds the inside ground cable. I then attached this cable to the tractor frame using the nearest transmission cover bolt. It is not original and may not look as neat but it eliminates an inherent weakness in the Cub grounding system.
The battery box brings up another frequent ground problem with Cubs. Wet cell batteries that use elecrolyte off gas naturally when charging and some of the acid laden electrolyte can eventually run down the sides of the battery to the bottom of the box. This eats up the bottom of the battery box and destroys the ground contact to the tractor frame. Worse yet, it will happen slowly and is mostly invisible. What I did in one situation where the bottom of the box had deteriorated to the point where good contact was no longer certain was to attach another ground cable on the outside of the box using the same bolt that goes through the box and holds the inside ground cable. I then attached this cable to the tractor frame using the nearest transmission cover bolt. It is not original and may not look as neat but it eliminates an inherent weakness in the Cub grounding system.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 25
- 565
-
by tst
Fri Jan 19, 2024 5:19 pm
-
- 1
- 162
-
by Jim Becker
Thu Feb 15, 2024 7:29 pm
-
- 12
- 394
-
by inairam
Wed Oct 26, 2022 3:09 pm
-
-
Voltage regulator VR851 -bad? Attachment(s)
by brewzalot » Wed Nov 09, 2022 11:57 am » in Farmall Cub - 18
- 619
-
by halftonstude
Sun Nov 27, 2022 2:10 pm
-
-
-
Mystery thingamabob on Voltage Regulator Attachment(s)
by TinkerBolt » Sat Jun 26, 2021 9:17 pm » in Farmall Cub - 14
- 620
-
by ajhbike
Tue Aug 24, 2021 7:28 am
-
Who is online
Users browsing this forum: No registered users and 2 guests