If I recall correctly, there was a thread a while back (well...quite a while back) that showed a how-to for retrofitting the pancake lights with the teardrop reflector. I looked in the how-to section under electrical, and cannot seem to find it.
Thanks for any help you all can give...
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Retrofitting pancake light thread?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
-
- 10+ Years
-
- Team Cub
- Posts: 24272
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
Re: Retrofitting pancake light thread?
I see those are in the sheet metal forum. I will move them to the ignition/electrical forum to cause less confusion.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 10+ Years
- Posts: 311
- Joined: Thu Feb 06, 2003 4:08 pm
- Zip Code: 47421
- eBay ID: gotowin
- Tractors Owned: 55 cub,
74 cub,
Cub Cadet 1515,
Case 580B TLB,
53 Ford Jubilee,
MF 271XE,
JD 3130,
JD gater - Location: Bedford, IN
Re: Retrofitting pancake light thread?
Here is the 2 post bulb in my pancake light.
Dan Robertson
We all make mistakes
I try to keep mine to a minimum
We all make mistakes
I try to keep mine to a minimum
-
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
Re: Retrofitting pancake light thread?
Dan, do you have any pics of how you wired and fit yours into those housings?
-
- 10+ Years
- Posts: 311
- Joined: Thu Feb 06, 2003 4:08 pm
- Zip Code: 47421
- eBay ID: gotowin
- Tractors Owned: 55 cub,
74 cub,
Cub Cadet 1515,
Case 580B TLB,
53 Ford Jubilee,
MF 271XE,
JD 3130,
JD gater - Location: Bedford, IN
Re: Retrofitting pancake light thread?
No pics showing the details, and it has been a few years since this was done. Seems there was a couple of glass tabs on the back side of the bulb near the outer edge that I had to grind down some with a high speed grinder. I was successful in doing this without breaking either of the bulbs. The screw lugs on the back were pressed down as close to the back of the bulb as possible. Two wraps of electrical tape around the outer edge of the bulb to hold it tight in the housing. The existing hole in the back of the pancake housing was plugged with a plumbers rubber plug cap like you see on some new fittings etc. A smaller hole allowing the wires to exit the pancake housing. I don't remember needing any other insulating material between the bulb screws and the back of the housing. I could be wrong though. This was done in 2005 and they continue to work great yet today.
Dan Robertson
We all make mistakes
I try to keep mine to a minimum
We all make mistakes
I try to keep mine to a minimum
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2
- 217
-
by 1953vacub
Tue Mar 28, 2023 8:37 am
-
- 1
- 225
-
by Eugene
Sat Oct 16, 2021 7:59 pm
-
- 13
- 989
-
by Glen
Sat Aug 19, 2023 1:15 am
-
-
Another Generator / Changing thread Attachment(s)
by AndrewSpencer » Sun Oct 23, 2022 9:57 am » in Farmall Cub - 6
- 281
-
by Jim Becker
Sun Oct 23, 2022 8:59 pm
-
-
- 5
- 250
-
by Stanton
Fri Jun 17, 2022 7:36 am
Who is online
Users browsing this forum: Majestic-12 [Bot], Masmith and 7 guests