Today i tried to fire up the farmall after sitting stil for i think a long time.
New plugs,leads,ignition coil and battery.
I poured some gas in the carbu through the feeder pipe and tried to start. Nothing
Shot some brake cleaner in to the carbu air inlet nothing
Removed a spark plug and shot some brake cleaner in there, refitted and a little pouf.
Then i started with my hand on the airintake side of the carbu (air filter is disconnected) and it workt a little.
I tried again and it started,however it only runs with the coke full open and the gas lever at the starting position.
Touching the gas ore choke and it stalls, putting little shots of break cleaner in it and it stays running.
Looking at the screws off the carbu the bowl seems to be removed a lot of times, screws are worn.
Wath now a new carbu ( expensive here in belgium)
Any andvice welcome
Steven
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Farmall cub not running
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 13
- Joined: Thu Feb 21, 2013 11:34 am
- Zip Code: 00000
-
- Team Cub Mentor
- Posts: 20389
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Farmall cub not running
Remove the main jet from the carburetor and using a small/thin soft wire clean the orifice.
Inexpensive try is to put carburetor/fuel system cleaner in the gas tank. Obtained from auto parts store. Then start and operate engine.
Complete carburetor kits are much less expensive than a replacement carburetor and they can be rebuilt.
If you haven't done so, compression test, first dry then wet.
Double check you ignition timing. Plug wires on correct spark plug.
Inexpensive try is to put carburetor/fuel system cleaner in the gas tank. Obtained from auto parts store. Then start and operate engine.
Complete carburetor kits are much less expensive than a replacement carburetor and they can be rebuilt.
If you haven't done so, compression test, first dry then wet.
Double check you ignition timing. Plug wires on correct spark plug.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 13
- Joined: Thu Feb 21, 2013 11:34 am
- Zip Code: 00000
Re: Farmall cub not running
I did a compression test, 7-6-8-8 bar is this good enough ?
The plug wires i cheked with another cub i have standing they are the same.
Ignition timing how ? i have a timing light however there are no degree markings on the pulley.
When starting there is a bit of gas dripping from the air intake on the carbu on to the ground ( flooding of the carb ?)
Thanks Steven
The plug wires i cheked with another cub i have standing they are the same.
Ignition timing how ? i have a timing light however there are no degree markings on the pulley.
When starting there is a bit of gas dripping from the air intake on the carbu on to the ground ( flooding of the carb ?)
Thanks Steven
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: Farmall cub not running
Careful on the visual comparison of the sparkplug wires. if the distributor was ever installed out of time, the wires may have been arranged to remedy the problem .
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- Team Cub Mentor
- Posts: 20389
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Farmall cub not running
The compression readings are in the pretty good to very good range. Good enough for an initial engine start up. I only used a conversion chart to convert 6 bar to psi which came out to 86 psi.
Operators manual. Top of page under manuals. Free down load. There is a section on ignition timing and timing marks. There is a pointer on the left front side of engine. The timing mark or marks are horizontal grooves in the crankshaft pulley. Depending on the age of the engine there may be only 1 groove which is the TDC mark. Two grooves, the first groove to match the pointer is 16 degrees before TDC.
Engine will run on 2 cylinders. Check the operator's manual for spark plug wire location.
Typically we static time the ignition system. Then use the timing light to double check the advance.
The distributor must be timed to the engine. If you are off a tooth or two the engine may run - badly. The rotor in the distributor must be set so that it points directly at the spark plug cap tower when firing that particular cylinder.
Operators manual. Top of page under manuals. Free down load. There is a section on ignition timing and timing marks. There is a pointer on the left front side of engine. The timing mark or marks are horizontal grooves in the crankshaft pulley. Depending on the age of the engine there may be only 1 groove which is the TDC mark. Two grooves, the first groove to match the pointer is 16 degrees before TDC.
Engine will run on 2 cylinders. Check the operator's manual for spark plug wire location.
Typically we static time the ignition system. Then use the timing light to double check the advance.
The distributor must be timed to the engine. If you are off a tooth or two the engine may run - badly. The rotor in the distributor must be set so that it points directly at the spark plug cap tower when firing that particular cylinder.
I have an excuse. CRS.
-
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: Farmall cub not running
While a number of things can be wrong, sounds like it has started with choking assist, just will not keep running. Visually check the sediment bulb under the tank and see how much crud is in it. If you should have a rubber gas line, pull one end off the carb and turn the gas on to check the flow, or check it throught the carb when you pull the carb main jet to clean it. Be sure not to enlarge the small hole in the jet, use a small copper,soft wire. use something to catch the gas, and turn the gas on to see how much comes out of the carb. It should be a good flow.
-
- 10+ Years
- Posts: 13
- Joined: Thu Feb 21, 2013 11:34 am
- Zip Code: 00000
Re: Farmall cub not running
ok thanks for the info, it sounds likes it fires on 4 pistons. however only runs on high idle.
The main jet is is different from i think because my farmall are the french kind.
Keep you guys posted
The main jet is is different from i think because my farmall are the french kind.
Keep you guys posted
-
- 10+ Years
- Posts: 13
- Joined: Thu Feb 21, 2013 11:34 am
- Zip Code: 00000
Re: Farmall cub not running
I runs like a dream and starts perfect.
Fitted a new carbu and wham it starts perfect even after a week of standstill !
Fitted a new carbu and wham it starts perfect even after a week of standstill !
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Farmall cub not running
Steven:
Do you have the Solex carb?
Do you have the Solex carb?
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 13
- Joined: Thu Feb 21, 2013 11:34 am
- Zip Code: 00000
Re: Farmall cub not running
I have fitted a new carbu it looks like the same however not a solex.
Only, on idle it wil run however when i press the clutch in, and if i don't give gas it will stop
Idle screw is @ max and this is not very high in rpm.
I haven't checked the ignition timing maybey this will help.(don't think so)
However the starting is beautiful, just choke a bit off gas start and let the choke go and it runs like clockwork
According to the manual there has to be oil in the governor, don't see where i must put it in
Regads Steven
Only, on idle it wil run however when i press the clutch in, and if i don't give gas it will stop
Idle screw is @ max and this is not very high in rpm.
I haven't checked the ignition timing maybey this will help.(don't think so)
However the starting is beautiful, just choke a bit off gas start and let the choke go and it runs like clockwork
According to the manual there has to be oil in the governor, don't see where i must put it in
Regads Steven
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Farmall cub not running
Steven:
A Cub at idle should be somewhere around 400 - 600 rpm's. If you push in the clutch, it is going to die ... period. 400 - 600 rpms is simply not enough for the Cub to do anything with. My timing is bang on, firing order is correct, governor operates as it should as does the carb and the rest of the fuel circuit. When I get up on the seat and I am ready to do anything with Ellie, I automatically increase the throttle .. then it doesn't stall/quit.
Give it some gas.....
As far as adding oil to the governor ... I don't see that in any manual. Here is a good article on rebuilding one and it shows all the steps - and I don't see adding oil anywhere. Grease on reassembly yes, oil no. Lurker Carl's Cub Governor Rebuild.
A Cub at idle should be somewhere around 400 - 600 rpm's. If you push in the clutch, it is going to die ... period. 400 - 600 rpms is simply not enough for the Cub to do anything with. My timing is bang on, firing order is correct, governor operates as it should as does the carb and the rest of the fuel circuit. When I get up on the seat and I am ready to do anything with Ellie, I automatically increase the throttle .. then it doesn't stall/quit.
Give it some gas.....
As far as adding oil to the governor ... I don't see that in any manual. Here is a good article on rebuilding one and it shows all the steps - and I don't see adding oil anywhere. Grease on reassembly yes, oil no. Lurker Carl's Cub Governor Rebuild.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- Similar Topics
- Replies
- Views
- Last post
-
- 7
- 276
-
by Clemsonfor
Sun Oct 10, 2021 7:57 pm
-
- 5
- 140
-
by Jim Becker
Mon Mar 18, 2024 2:17 pm
-
- 7
- 305
-
by Glen
Wed Feb 28, 2024 4:30 pm
-
- 8
- 342
-
by smallfarm
Mon Jul 17, 2023 6:35 am
-
- 19
- 780
-
by Eugene
Mon Oct 17, 2022 9:33 am
Who is online
Users browsing this forum: Milli and 2 guests