This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cub has no spark
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 6
- Joined: Mon Apr 14, 2014 8:20 pm
- Zip Code: 73089
Cub has no spark
Hello
Just joined the forum. I've been lurking and reading old posts trying to find some ideas. I have a 49 cub with magneto. It's been barn kept and looks fine but won't start. It is a 6 volt positive ground tractor.
I have replaced the battery and spark plugs. I have put a spark checker on it and there is nothing at all. From what I've read I'm tempted to think it may be the coil? Is there a way to check coil on the tractor? If it's bad, I was thinking about testing it with an external coil before I replace it. Again from what I've read I run the positive from the coil to ground. The negative to a switch, other side of switch to negative of battery? Is there a 6 volt coil commonly available from napa, oreilly or autozone that would not need a resistor? Or are resistors only needed on 12 volt? I have seen c809 at autozone, it's a 6 volt coil. Would this work to test it.
Next question seems a little silly, but I haven't seen the answer around yet. It has the sickle mower. I know where you raise the hydraulics at, but where do you start the pto at? Only thing I've seen that I think might be it is next to the gear lever, a tiny little lever? Is this what starts the pto?
Thanks for all the help. I really want to get the cub running again.
Just joined the forum. I've been lurking and reading old posts trying to find some ideas. I have a 49 cub with magneto. It's been barn kept and looks fine but won't start. It is a 6 volt positive ground tractor.
I have replaced the battery and spark plugs. I have put a spark checker on it and there is nothing at all. From what I've read I'm tempted to think it may be the coil? Is there a way to check coil on the tractor? If it's bad, I was thinking about testing it with an external coil before I replace it. Again from what I've read I run the positive from the coil to ground. The negative to a switch, other side of switch to negative of battery? Is there a 6 volt coil commonly available from napa, oreilly or autozone that would not need a resistor? Or are resistors only needed on 12 volt? I have seen c809 at autozone, it's a 6 volt coil. Would this work to test it.
Next question seems a little silly, but I haven't seen the answer around yet. It has the sickle mower. I know where you raise the hydraulics at, but where do you start the pto at? Only thing I've seen that I think might be it is next to the gear lever, a tiny little lever? Is this what starts the pto?
Thanks for all the help. I really want to get the cub running again.
-
- 10+ Years
- Posts: 3415
- Joined: Wed May 11, 2011 8:59 pm
- Zip Code: 39154
- Tractors Owned: 1969 Farmall Cub
1952 Cub
1942 Farmall H - Location: Raymond, MS
Re: Cub has no spark
Don't just start changing parts. May be as simple as filing the points.
That little lever engages pto. Depress clutch, shift the lever, let clutch out and pto should spin. A word of caution. Be careful when lifting the blade part of the sickle mower. The blade can and will slide on its own, so you don't want your fingers in the way. I highly reccomend reading the owners manual for the mower
That little lever engages pto. Depress clutch, shift the lever, let clutch out and pto should spin. A word of caution. Be careful when lifting the blade part of the sickle mower. The blade can and will slide on its own, so you don't want your fingers in the way. I highly reccomend reading the owners manual for the mower
Thomas
-
- 10+ Years
- Posts: 363
- Joined: Wed Aug 31, 2011 11:55 am
- Zip Code: 37058
- Tractors Owned: 1950 Cub, 1952 Cub, 1970 Cub, 1975 Cub, 1953 Cub, 1939 A, 1948 super A, 1952 super A, 1950 C demonstrator, 1952 Super C, 1949 H, 1956 farmall 300, 1957 international 350, 1963 Massey Ferguson 35
- Circle of Safety: Y
- Location: TN Dover
Re: Cub has no spark
Don't just start changing parts. May be as simple as filing the points
I would check the points before I did anything else. If it has been sitting for very long, I would also prime the oil pump.
-
- 10+ Years
- Posts: 6
- Joined: Mon Apr 14, 2014 8:20 pm
- Zip Code: 73089
Re: Cub has no spark
Sorry was trying to get my son to bed while trying to post.
I have downloaded the owners manual for cub from a link in an earlier post. I have filed and cleaned points with emery cloth. But I do need to check the gap. Is there a good way to get the rotor to line up with the #1 with an electric start? Or is it just trial until you get it right?
Thanks
I have downloaded the owners manual for cub from a link in an earlier post. I have filed and cleaned points with emery cloth. But I do need to check the gap. Is there a good way to get the rotor to line up with the #1 with an electric start? Or is it just trial until you get it right?
Thanks
-
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: Cub has no spark
Welcome to the forum from Arkansas. On timing a magneto watch this video.
http://www.youtube.com/watch?v=QqucExhxXdE
You can check the coil by temporarily putting on an external coil. Should try to use a point file when filing points to keep from leaving unwanted residue.
http://www.youtube.com/watch?v=QqucExhxXdE
You can check the coil by temporarily putting on an external coil. Should try to use a point file when filing points to keep from leaving unwanted residue.
-
- 10+ Years
- Posts: 4996
- Joined: Fri Oct 29, 2010 11:34 pm
- Zip Code: 36558
- Tractors Owned: Cubs: (3)'49's, (1 is for parts), (1)'57 IH Cub LoBoy w/FH, (2)154 Number Series Loboys, (1 is for parts), '76 Longstripe w/FH, Mowers: C-22, Bush Hog 412, Pennington 59, Woods RM42CF, Woods 42, assorted FCub plows, planters, discs, etc. OTHERS: '49 AC B & Ind. Sickle mower, '61 AC D12 Ser 2, '52 8N, '56 Ferguson 35 Deluxe, '47 & '49 Avery V, '53 MM BG (offset), '51 JD M (regular), '56 JD 420C, with Blade and fire plow, '85 JD 850 (Yanmar) w/72" belly mower, '76? Yanmar 2TR15 1500 & Bush Hog SQ42S-2 mower, '78? FORD Dexta, '86 FORD LGT14D & 48" Mower, (2)Cub Cadets & Mowers (MTD), (4) Sears Surburban's, other MTD mowers, Jeeps & other misc. "treasures"
- Circle of Safety: Y
- Location: AL (Southwest)
Re: Cub has no spark
Setting the cam on the shaft for points gap is basically trial and error unless you have a hand crank. You might be able to engage the pto shaft and set the transmissin in neutral the use the pto shaft to turn the cam to check the points gap. I''ve never done this but I have used the pto to align the input shaft to the engine/clutch for reconnection after splitting the tractor, so it might work.
Stan in LA (lower AL)
USAF & Reserves, Reg ARMY, ARMY NG (AL)
USAF & Reserves, Reg ARMY, ARMY NG (AL)
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Cub has no spark
If you don't have a hand crank you can remove the spark plugs to remove compression and turn the engine with the fan or by using the pulley on the pto shaft. If no pulley, you can put a pair of vice grips or pipe wrench on the pto shaft to turn it. Just don't forget to remove them before starting (don't ask why I added the last part).
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 7832
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: Cub has no spark
magneto points gap .013
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
-
- 10+ Years
- Posts: 6
- Joined: Mon Apr 14, 2014 8:20 pm
- Zip Code: 73089
Re: Cub has no spark
Well had the day off so I was able to spend a little time with the cub. Checked points gap again and got set to .013. Cleaned a couple of the connections and checked magneto timing. All looked good. I ended up pulling the magneto to take it apart to check everything. I've seen nothing that jumps out as bad. So I'm wondering if I can reassemble and bench test a magneto? If I spin it by hand should I see a spark at the points? Is there a good way to check the coil? It looks fine but I'd like to know if I can check it while it's out?
Thanks for all the help.
Thanks for all the help.
-
- 10+ Years
- Posts: 42
- Joined: Fri Apr 18, 2014 4:46 pm
- Zip Code: 66111
- Tractors Owned: 1928 McCormick Deering 10-20,1949 Cub.
Re: Cub has no spark
HI 49 cub in ok I have a 49 cub also with a magneto it started running like a deere and then died would not start no spark filed and reset points still noting. removed magneto took cap off of coil it was toast .put new coil in good blue spark.
-
- 10+ Years
- Posts: 363
- Joined: Wed Aug 31, 2011 11:55 am
- Zip Code: 37058
- Tractors Owned: 1950 Cub, 1952 Cub, 1970 Cub, 1975 Cub, 1953 Cub, 1939 A, 1948 super A, 1952 super A, 1950 C demonstrator, 1952 Super C, 1949 H, 1956 farmall 300, 1957 international 350, 1963 Massey Ferguson 35
- Circle of Safety: Y
- Location: TN Dover
Re: Cub has no spark
So I'm wondering if I can reassemble and bench test a magneto? If I spin it by hand should I see a spark at the points? Is there a good way to check the coil?
Yes, yes, and yes.
be careful to turn the magneto in the proper direction. You should feel a spring that is holding you back, but with enough force it will trip and that is when it should fire.
-
- 10+ Years
- Posts: 6
- Joined: Mon Apr 14, 2014 8:20 pm
- Zip Code: 73089
Re: Cub has no spark
Update:
I have a spark now! While the magneto was apart and off tractor I cleaned and checked every connection. Reassembled and set points and retimed it, twice.
I still had the spark checker on it and tried cranking and had spark right away. Then realized I had no gas for the cub so went and got gas and put some in. Nothing. Gas ran out of every orifice in the carb while I was trying to start!
Pulled off the carb and started inspecting. The float was difficult to remove from the bowl there was so much white gunk built up. So the bowl is soaking overnight in carb cleaner and the float is gonna get brushed off in the am. I've cleaned the jet already so I'm hoping with a good carb cleaning it will light off in the morning. A couple times it tried to catch but never would.
Will hopefully reassemble the carb tomorrow and run it.
Thanks to all for the help!
I have a spark now! While the magneto was apart and off tractor I cleaned and checked every connection. Reassembled and set points and retimed it, twice.
I still had the spark checker on it and tried cranking and had spark right away. Then realized I had no gas for the cub so went and got gas and put some in. Nothing. Gas ran out of every orifice in the carb while I was trying to start!
Pulled off the carb and started inspecting. The float was difficult to remove from the bowl there was so much white gunk built up. So the bowl is soaking overnight in carb cleaner and the float is gonna get brushed off in the am. I've cleaned the jet already so I'm hoping with a good carb cleaning it will light off in the morning. A couple times it tried to catch but never would.
Will hopefully reassemble the carb tomorrow and run it.
Thanks to all for the help!
-
- 10+ Years
- Posts: 6
- Joined: Mon Apr 14, 2014 8:20 pm
- Zip Code: 73089
Re: Cub has no spark
Well a little disappointed now. Reassembled carb and tried again and still not running. Pulled the plugs and rear two were black and sooty and front two were clean, but all were dry. So, I'm thinking about a carb rebuild kit now. Or would I be better off purchasing a new carb? Or is there a different direction I should be looking?
Thanks again for the help
Thanks again for the help
-
- Cub Pro
- Posts: 2779
- Joined: Sun Jul 01, 2007 10:07 pm
- Zip Code: 29518
- Circle of Safety: Y
- Location: SC, Cades 29518
Re: Cub has no spark
Since you have spark this may be a little late, but don't "snap" the magneto over without giving the spark somewhere to ground to. That will fry a coil. So next time make sure the internal coil can send the spark to the magneto housing with a piece of spark plug wire. I will assume you static timed the magneto correctly, there are a couple of videos to help with that on this forum.
Now that you have spark, sounds like the carb may be the culprit. Was the idle tube intact when you took the carb apart (long tube screwed into carb top that extends into a reservoir in carb bottom)? Did you open up the two small ports in the carb venturi right above the butterfly plate? Are you sure the orifice in the main jet is clean? Did you reset the idle mixture screw to 1.5 turns out. That screw adjusts air, by the way, so out is leaner, in is richer. There is a carb "how-to" on here somewhere as well. Lastly, did the two carb bodes need straightening at the joint; there is a fixture for this, and information on this forum about how to make one.
Lastly, do NOT buy a carb kit from just anywhere, many are junk. Case IH (expensive) is the best, and Steiner sells a good kit for less money. TSC kits from Tisco are junk.
Now that you have spark, sounds like the carb may be the culprit. Was the idle tube intact when you took the carb apart (long tube screwed into carb top that extends into a reservoir in carb bottom)? Did you open up the two small ports in the carb venturi right above the butterfly plate? Are you sure the orifice in the main jet is clean? Did you reset the idle mixture screw to 1.5 turns out. That screw adjusts air, by the way, so out is leaner, in is richer. There is a carb "how-to" on here somewhere as well. Lastly, did the two carb bodes need straightening at the joint; there is a fixture for this, and information on this forum about how to make one.
Lastly, do NOT buy a carb kit from just anywhere, many are junk. Case IH (expensive) is the best, and Steiner sells a good kit for less money. TSC kits from Tisco are junk.
Rick Spivey
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
-
- 10+ Years
- Posts: 6
- Joined: Mon Apr 14, 2014 8:20 pm
- Zip Code: 73089
Re: Cub has no spark
Hello and thank you for the replies. The long tube was attached. I did not know about the two ports above the butterfly so I definitely need to check those. The main jet I cleaned out a while back when I first got it so I think it's fine. The idle screw, which one is that? I need to find a diagram of the carb it looks like.
On the ih rebuild kit, is it ftc825? Is this the correct part number?
Thanks again for all the help
On the ih rebuild kit, is it ftc825? Is this the correct part number?
Thanks again for all the help
-
- Similar Topics
- Replies
- Views
- Last post
-
- 4
- 204
-
by AL Farmall Boy
Wed Mar 06, 2024 12:12 pm
-
- 22
- 657
-
by Glen
Wed Feb 07, 2024 7:45 pm
-
- 1
- 112
-
by SamsFarm
Tue May 04, 2021 4:56 pm
-
- 7
- 579
-
by Royalwulff24
Sun Dec 10, 2023 4:34 pm
-
- 2
- 519
-
by Bill V in Md
Tue Dec 12, 2023 7:35 am
Who is online
Users browsing this forum: No registered users and 4 guests